fbpx

794 AC Mining Truck

Designed and manufactured by Caterpillar, the 794 AC electric drive truck is single sourced from one manufacturer and supported by the best dealer network. The 794 AC is designed to:
  • Deliver a true 297tonnes (327tons) capacity
  • Deliver reliability and uptime
  • Deliver easy serviceability
  • Deliver low owning and operating cost
  • Deliver operator confidence with four corner wet disc blended service brakes and traction control
The 794 AC is built to deliver to your bottom line.

Nominal Rated Payload 297 t
Rated Gross Machine Weight 521631 kg
Chassis Weight 193338 kg
Body Weight 29187 kg
Note (1) Consult your tire manufacturer for maximum tire load.
Note (2) Chassis weight with full fuel and fluids, standard & mandatory attachments, hoist, body mounting group, rims, and tires
Note (3) Refer to Cat Mining Truck 10/10/20 Overload Policy (AEXQ0250) for maximum gross machine weight limitations.
Note (4) Tier 4 Final / Stage V chassis weight: 426312 lb (193372 kg)

Engine Model Cat® C175-16
Standard Gross Power - SAE J1995 2610 kW
Optional Gross Power - SAE J1995 2312 kW
Optional Gross Power - SAE J1995 (Option 2) 2051 kW
Emissions Rating Fuel Optimized
Bore 175 mm
Stroke 220 mm
Displacement 85 l
Rated Speed 1800 r/min
Gross Power - SAE J1995 2610 kW
Net Power - SAE J1349 2539 kW
Note (1) Contact factory for high altitude configuration.
Note (2) Tier 4 / EU Stage V option available for regions that require these emissions standards.
Note (3) Tier 4 / EU Stage V engine option Net Power - SAE J1349: 3434 HP (2561 kW)

Total Reduction Ratio 35:1
Top Speed - Loaded 60 km/h
Generator/Alternator Brushless, engine mounted, dual bearing
Controls IGBT Inverter Technology, air cooled, pressurized cabinet with filtration
Wheel Motor High-torque AC induction, rear axle mounted
Cooling System Variable speed, hydraulically driven cooling system

Service Brakes Four-Corner, Wet Disc, Oil Cooled, Hydraulically Actuated
Front Wet Disc Brake Surface Area 131473 cm²
Rear - Wet Disc Brake Surface Area 198388 cm²
Standards ISO 3450:2011
Load Brake Rear service brakes
Dynamic Retarding Power - Continuous 4086 kW
Parking Brake Four-corner, Multi-disc, Spring applied, Hydraulically Released

Pump Flow - High Idle (HAA at 1,800 rpm) 840 l/min
Pump Flow - High Idle (LAA at 1,960 rpm) 910 l/min
High Idle Body Lower Time - Float 20 s
Total Cycle Time 44 s
Relief Valve Setting - Raise 20884 kPa
Body Raise Time - High Idle 24 s
Note (1) Twin, two-stage hydraulic cylinders mounted inside main frame; double-acting cylinders in both stages.
Note (2) Power raise in both stages; power down in both stages possible.
Note (3) Automatic body-lower modulation reduces impact on frame.

Struck 108-133 m³ (142-175 yd³)
Heaped (SAE 2:1) 180-222 m³ (236-290 yd³)
Dump Body Plate Thickness Varies Depending on Body Selection - Floor Plate 16 mm
Dump Body Plate Thickness Varies Depending on Body Selection - Front Plate 9 mm
Dump Body Plate Thickness Varies Depending on Body Selection - Side Plate 8 mm
Dump Body Plate Thickness Varies Depending on Body Selection - Canopy Plate 5 mm
Note Contact your local Cat dealer for body recommendations.

Steering Standards ISO 5010:2007
Steer Angle 39 °
Note Gross Machine Operating Weight is 521 631 kg (1,150,000 lb).

Standard Tires 53/80 R63
Rims 36" x 63"
Note (1) Quick Change Rims optional.
Note (2) Caterpillar recommends the customer evaluate all job conditions and consult tire manufacturer for proper tire selection and TKPH (TMPH) capabilities.

Height - Top of ROPS 6779 mm
Overall Length 15463.5 mm
Rear Axle - Tail 4716 mm
Dump Clearance 1555 mm
Loading Height - Empty 6995 mm
Overall Height - Body Raised 14747 mm
Centerline Front Tire Width 7024 mm
Front Axle Clearance 969 mm
Canopy Width (without optional rock deflectors) 9068 mm
Outside Body Width 9062 mm
Inside Body Width 8560 mm
Front Canopy Height 8024 mm
Rear Axle - Clearance 934 mm
Centerline of Rear Dual Tire Width 5727 mm
Overall Tire Width 8738 mm
Wheel Base 6644.5 mm
Overall Canopy Width 9611 mm
Ground Clearance 906 mm

Final Drive - Each 254 l
Fuel Tank 4922 l
Cooling System 799 l
Crankcase 310 l
Hydraulic System - Including Tank 1458 l
Hydraulic Tank 1121 l
Note (1) DEF Tank only available for EPA Tier 4 / EU Stage V engine option.
Diesel Exhaust Fluid Tank 378 l

Front Axle - Empty 49 %
Front Axle - Loaded 33 %
Rear Axle - Empty 51 %
Rear Axle - Loaded 67 %

Total Reduction Ratio 35:1

FOPS Standards FOPS (Falling Object Protective Structure) meets ISO 3449:1992.
ROPS Standards ROPS (Rollover Protective Structure) meets ISO 3471:1994.

Sound Standards (1) The operator sound pressure level measured according to work cycle procedures specified in ISO 6394 and 6396 is 75 dB(A) for cab offered by Caterpillar when properly installed, maintained, and tested with doors and windows closed.
Sound Standards (2) Hearing protection may be needed when operating with an open operator station and cab (when not properly maintained or doors/windows open) for extended periods or in a noisy environment.

Ask Quotation

Usados

SOLUTIONS THAT SIMPLIFY

(Free) 800 206 707

STET
Websites